Part number: 651

Vertical wall mount holder for all wands. Fixing is by self-adhesive pad, or alternatively this can be removed to use the two countersunk fixing holes. Material: acrylic resin.

Part number: 652

Horizontal desktop holder for all wands. This stand is intended for normally closed wands, but can be used with any wand. Material: acrylic resin.

Part number: 658

Vertical wall mount holder for all normally open wands. Vacuum is isolated (switched off) while the wand is in the stand. Fixing is by self-adhesive pad, or alternatively this can be removed to use the two countersunk fixing holes. Material: acrylic resin.

Part number: 659

Horizontal desktop holder for all normally open wands. Vacuum is isolated (switched off) while the wand is in the stand. Material: acrylic resin.

Part number: 808

Kit of parts for changing filters (including two replacement HEPA filters) for FV-30 and FV-60 pumps.

Part number: 809

Replacement filter for FV-10 pumps.

Part number: 820

Special tubing for vacuum/blow pump FV-W-240 and F007 wand.

Part number: 848

Part number: 849

Part number: 850-M

Straight, flexible ESD safe tubing. 3 mm ID, 5 mm OD. Sold per metre.

Part number: 851-L

Black, coiled flexible tubing. Extends easily to over 2 m. Can be used with any wand. ESD safe when used with C series wands. 4 mm ID, 6 mm OD. Note that our wands accept both 3 and 4 mm ID tubing.

Part number: 851-M

Black, coiled flexible tubing. Extends easily to over 2 m. Can be used with any wand. ESD safe when used with C series wands. 3 mm ID, 5 mm OD. Note that our wands accept both 3 and 4 mm ID tubing.

Part number: 858

ESD grounding kit for all vacuum pumps.

Part number: 901

Vacuum wand tip condition tester. Wand tips can become less efficient with use if the contact surface deteriorates due to minute scratches, etc. This device can be used to check that the wand is performing correctly. The tip contact parts are made of PPS (polyphenylsulphide).

Part number: 930

Allen key for wand button.

Part number: F007

Part number: FV-10-110

Datasheet

Our smallest vacuum pump, the FV-10 is designed to minimise noise and has variable vacuum pressure, making it suitable for a wide range of applications. Used with a suitable wand and suction cup, the pump will lift in excess of 150 g in weight. Supplied with 1 m clear flexible vacuum tubing and in-line power switch.

• Designed to minimise noise generation
• Adjustable Vacuum Pressure: -4kPa to -14kPa
• Flow Rate: 2.7
• l/min Power Requirement: 100-120 VAC
• Consumption Power: 5.0 W
• Duty Cycle: Continuous
• Life Expectancy > 8760 hours
• Dimensions (D x W x H): 155 x 72 x 54 mm
• Net weight: 600 g
• Static-Dissipative Grounding Kit (Accessory)
• ESD Safe Tubing (Accessory) Inlet Filter (Accessory)
• Gross weight: 650 g

Part number: FV-10-240

Datasheet

Our smallest vacuum pump, the FV-10 is designed to minimise noise and has variable vacuum pressure, making it suitable for a wide range of applications. Used with a suitable wand and suction cup, the pump will lift in excess of 150 g in weight. Supplied with 1 m clear flexible vacuum tubing and in-line power switch.

• Designed to minimise noise generation
• Adjustable Vacuum Pressure: -4kPa to -14kPa
• Flow Rate: 2.7 l/min
• Power Requirement: 240 VAC
• Consumption Power: 5.0 W
• Duty Cycle: Continuous
• Life Expectancy > 8760 hours
• Dimensions (D x W x H): 155 x 72 x 54 mm
• Net weight: 600 g
• Static-Dissipative Grounding Kit (Accessory)
• ESD Safe Tubing (Accessory)
• Inlet Filter (Accessory)
• Gross weight: 650 g

Part number: FV-30-110

Datasheet

The FV-30 is our mid-range vacuum pump. It is capable of safely handling up to 6 inch (150 mm) wafers (when used with a suitable wand), and is suitable for a wide range of other applications. Fitted with replaceable HEPA filters in both inlet and outlet. Supplied with 1 m clear flexible vacuum tubing.

• Flow rate 2.5 l/min (0.088 cfm)
• Ultimate pressure -300 mmHg (-40 kPa)
• Power supply 100-120 VAC
• Built in inlet and outlet HEPA filters
• Oil-free for cleanroom use
• Long term high reliability Designed to minimize noise generation
• Nylon body for static protection
• Compact design
• ESD Safe Tubing (Accessory)
• Static-Dissipative Grounding Kit (Accessory)
• HEPA Filter Kit (Replacement Part)
• Compliance with CE regulations
• HEPA filters trap 99.97% of all particles down to 0.3 microns
• The FIlter windows indicate when to change HEPA filters
• Gross weight: 860 g

Part number: FV-30-240

Datasheet

The FV-30 is our mid-range vacuum pump. It is capable of safely handling up to 6 inch (150 mm) wafers (when used with a suitable wand), and is suitable for a wide range of other applications. Fitted with replaceable HEPA filters in both inlet and outlet. Supplied with 1 m clear flexible vacuum tubing.

• Flow rate 2.5 l/min (0.088 cfm)
• Ultimate pressure -300 mmHg (-40 kPa)
• Power supply 240 VAC
• Built in inlet and outlet HEPA filters
• Built in inlet and outlet HEPA filters
• Oil-free for cleanroom use
• Long term high reliability Designed to minimize noise generation
• Nylon body for static protection
• Compact design
• ESD Safe Tubing (Accessory)
• Static-Dissipative Grounding Kit (Accessory)
• HEPA Filter Kit (Replacement Part)
• Compliance with CE regulations
• HEPA filters trap 99.97% of all particles down to 0.3 microns
• The FIlter windows indicate when to change HEPA filters
• Gross weight: 860 g

Part number: FV-60-110

Datasheet

The FV-60 is our largest clean room vacuum pump. It is capable of safely handling up to 12 inch (300 mm) wafers (when used with a suitable wand), and is suitable for a wide range of other applications. Fitted with replaceable HEPA filters in both inlet and outlet. It is oil-free for use in the cleanroom and designed for long term high reliability with minimal noise generation. Supplied with 1 m clear flexible vacuum tubing.

• Flow Rate
• 2.5 l/min (0.088 cfm)
• Ultimate pressure -600 mmHg (-80 kPa)
• Power supply 100-120 VAC
• Built in inlet and outlet HEPA filters
• Nylon body for static protection
• Compact design
• ESD Safe Tubing (Accessory)
• Static-Dissipative Grounding Kit (Accessory)
• HEPA Filter Kit (Replacement Part)
• Compliance with CE regulations
• HEPA filters trap 99.97% of all particles down to 0.3 microns
• The FIlter windows indicate when to change HEPA filters
• Gross weight: 1400 g

Part number: FV-60-240

Datasheet

The FV-60 is our largest clean room vacuum pump. It is capable of safely handling up to 12 inch (300 mm) wafers (when used with a suitable wand), and is suitable for a wide range of other applications. Fitted with replaceable HEPA filters in both inlet and outlet. It is oil-free for use in the cleanroom and designed for long term high reliability with minimal noise generation. Supplied with 1 m clear flexible vacuum tubing.

• Flow rate 2.5 l/min (0.088 cfm)
• Ultimate pressure –600 mmHg (–80 kPa)
• Power supply 240 Vac
• Built in inlet and outlet
• HEPA filters
• Nylon body for static protection
• Compact design
• ESD safe tubing (accessory)
• Static dissipative grounding kit (accessory)
• HEPA filter kit (replacement part)
• Compliance with CE regulations
• HEPA filters trap 99.97% of all particles down to 0.3 microns
• The filter windows indicate when to change HEPA filters
• Gross weight: 1400 g

Part number: FV-W-240

Datasheet

This unique pump acts like a normal vacuum pump for handling lightweight objects, but includes a gentle, adjustable blowing function that ensures careful and precise release. It is used with our specially designed PTFE F007 vacuum wand and 820 tubing. Lightweight objects include contact lenses, restoration pieces, thin die etc. Built-in HEPA filters trap 99.97% of all particles down to 0.3 microns.

• Vacuum Pump for DuoVac: The blowing function ensures secure release of light weight objects
• Built in inlet and outlet HEPA filters
• Nylon body for static protection
• Suction Power: -30kPa (fixed)
• Adjustable Blowing Power: 0-10kPa
• Flow Rate: 1.2 l/min
• Power supply: 240 VAC
• PVC double tubing (not included)
• HEPA Filter Kit (replacement part)
• Filter windows indicate when to change filters
• This pump works only with the Normally Open with Blow valve wand F007
• Gross weight: 850 g